ON PERFECTION OF CONSTRUCTIVE AND TECHNOLOGICAL FORMS OF PLATE AND RIBBED TRANSFER STRUCTURES FROM GLUED TIMBER
https://doi.org/10.26518/2071-7296-2019-1-76-89
Abstract
Introduction. The paper presents the prefabricated whole-glued slab-ribbed superstructures, containing glued beams (fins) and a multi-layered wood-panel from horizontal cross-layers of blank boards, laid successively on glued beams and each other and interconnected by glue seams.
Materials and methods. Because of the development of the constructive and technological forms of the considered superstructures, the authors propose the structure composed of plate and ribbed integrally transported prefabricated sections with the width of 3-3.5 m. The authors highlight that the combined action of the detached sections is provided through the nodes of combination on the adjacent ribs of the sections without the complicated compression of all the elements of the superstructure including beams, plates, and diaphragms.
Results. The analysis of the stress-deformed span by two methods indicates that both methods determine, with a sufficient degree of accuracy, the nature of the distribution of stresses and strains in sections of the structure. Moreover, the obtained values of the maximum deflections and stresses do not exceed the limit values established by the norms and the corresponding values in a similar construction of the structure with a solid timber slab.
Conclusions. The paper shows that the proposed construction with the division of the whole-glued multiridged span structure into separate prefabricated, factory-made sections would significantly expand the usage of laminated wood in bridge construction.
About the Authors
V. A. Utkin
Siberian State Automobile and Highway University
Russian Federation
Russian Federation
Doctor of Technical Sciences, Professor of the Bridges and Tunnels Department
644080, Omsk, 5, Mira Ave.
P. N. Kobzev
Siberian State Automobile and Highway University
Russian Federation
Russian Federation
Candidate of Technical Sciences, Associate Professor of the Bridges and Tunnels Department
644080, Omsk, 5, Mira Ave.
References
1. Utkin V.A., Kobzev P.N. Avtodorozhnye derevjannye mosty novogo pokolenija [Road wooden bridges of new generation]. Nauchnoe izdanie. Omsk, 2004: Izd-vo SibADI. 50 p. (in Russian)
2. Cesaro G. and Piva F. (2003): Timber Bridges – Design and durability. Master’s Thesis in the International Master’s programme in Structural Engineering/Department of Civil and Environmental Engineering Division of Structural Engineering Steel and Timber Structures. CHALMERS UNIVERSITY OF TECHNOLOGY - Göteborg, Sweden 2003.
3. Agnieszka Gilun, Julia Meronk: Stresslaminated timber T-beam and box-beam bridges. Master’s Thesis in the International Master’s programme in Structural Engineering/Department of Civil and Environmental Engineering Division of Structural Engineering Steel and Timber Structures. CHALMERS UNIVERSITY OF TECHNOLOGY - Göteborg, Sweden 2006.125 p.
4. Jobstl, R.A.; et. al. A Contribution to the Dising and System Effects of Cross Laminated Timber (CLT), Paper 39-12-4, Proceedings of CIB-W18, Florence, Italy, 2006.
5. Schickhofer, G.; Moosbrugger, T; (Ed.) Brettsperrholz – Ein Blick auf Forschung und Praxis. Proceedings, Gras Univerversity of Technology, Institute for Timber Engineering and Wood Technology, Gras. Austria, 2006 (in Germany).
6. Educational Materials for Designing and Testing of Timber Structures. HANDBOOK 1 Timber Structures. September 2008. P. 63–100, 209–227.
7. Sheila R. Duwadi; Michael A.: Ritter Timber bridges in the United States. P. 32–40 in Public roads Winter 1997, Vol 60, No.3.
8. Michael A. Ritter; Thomas G. Williamson; Russell C. Moody: Innovation in glulam timber bridge design. Pp 1298-1303 in Baker, N.C.; Goodno, B.J. (Ed.) Structures Congress 12: Proceedings of Structures Congress ’94; 24-28 April 1994; Atlanta, GA. New York: American Society of Civil Engineers; 1994, Vol.2.
9. Keith Crews; Stephen Bakoss: Fundamental structural behavior of “Built-up” stress-laminated timber bridge decks. P. 39–48 in Ritter, M.A.; Duwadi, S.R.; Lee, P.D.H. (Ed.) National Conference on Wood Transportation structures; 23–25 October 1996, Madison, WI: U.S. Department of Agriculture, Forest Service, Forest Product Laboratory.
10. James A. Kainz; James P. Wacker; Michael A. Ritter; Stan Bishop: Field performance of timber bridges: 21. Humphrey stress-laminated T-beam bridge. Res. Rap. FPL-RP-597. Madison, WI: U.S. Department of Agriculture, Forest Service, Forest Product Laboratory. 16 p.
11. James P. Wacker; Michael A. Ritter; Kim Stanfill-McMillan; Nikki T. Broun; Jonathon R. Becker: Field performance of timber bridges: 11. Spearfish Creek stress-laminated box-beam bridge. Res. Rap. FPL-RP-556. Madison, WI: U.S. Department of Agriculture, Forest Service, Forest Product Laboratory. 17 p.
12. Otto Kleppe; Eric Aasheim: Timber bridges in Nordic countries. Pp 10-16 in Ritter, M.A.; Duwadi, S.R.; Lee, P.D.H. (Ed.) National Conference on Wood Transportation structures; 23–25 October 1996, Madison, WI: U.S. Department of Agriculture, Forest Service, Forest Product Laboratory.
13. Tormod Dyken: Tynset Bridge. Nordic Road & Transport Research No.1. 2002.
14. Lehnitskij S.G. Anizotropnye plastinki [Anisotropic plates]. Moscow, Gostehizdat, 1957. 464 p. (in Russian)
15. Ambartsumjan S.A. Teorija anizotropnyh plastin. Prochnost’ ustojchivost’ i kolebanija [Theory of anisotropic plates. Durability stability and fluctuations]. Moscow, Izdatel’stvo «Nauka». 1967. 268 p. (in Russian)
16. Aleksandrov A.V., Laschenikov B.Ja., Shaposhnikov N.N., Smirnov V.A. Metody rascheta sterzhnevyh sistem, plastin i obolochek s ispol’zovaniem `EVM v 2-h chastjah. [Methods of the rod systems calculation, plates and covers with the computer, in 2 parts]. Moscow, Strojizdat, 1976. Ch.1. 248 p. Ch.2. 237 p. (in Russian)
17. Utkin V.A., Kadisov G.M. O metodah prostranstvennogo rascheta balochnyh proletnyh stroenij derevjannyh mostov s mnogoslojnoj proezzhej chast’ju iz kleenoj drevesiny [On methods of spatial calculation of frame flying structures of wooden bridges with the multilayered glued wood]. Izvestija vuzov. Stroitel’stvo, 2007, no 6, g. Novosibirsk, P.98–104. (in Russian)
18. Kuvshinov A.P. Vybor vneshnego davlenija pri skleivanii derevjannyh kleenyh konstruktsij. [Choice of external pressure when pasting wooden glued designs] Ref. inf. Serija IV Stroitel’naja industrija, 1976. Vyp. 12, P. 12–14. (in Russian)
19. Utkin V.A. Tehnologija izgotovlenija proletnyh stroenij iz kleenoj drevesiny s mnogoslojnoj plitoj proezzhej chaste [Manufacturing techniques of structures from glued wood with a multilayered plate of the carriageway]. Stroitel’nye materialy, 2007, no 5, P. 31–34. (in Russian)
20. Koval’chuk L.M. Proizvodstvo derevjannyh kleenyh konstruktsij. Izd. tret’e pererabotannoe i dopolnennoe [Production of wooden glued designs]. Moscow, RIF «Strojmaterialy», 2005. 336 p. (in Russian)
21. Polivanov N.I. Zhelezobetonnye mosty na avtomobil’nyh dorogah [Reinforced concrete bridges on highways]. Moscow, Nauchnotehnicheskoe izdatel’stvo avtotransportnoj literatury, 1956. P. 288–297. (in Russian)
22. Utkin V.A. Proektirovanie i stroitel’stvo balochnogo proletnogo stroenija iz kleenoj drevesiny [Design and construction of the frame structures from glued wood]. Problemy prochnosti materialov i sooruzhenij na transporte. Sbornik dokladov IX Mezhdunarodnoj konferentsii po problemam prochnosti materialov i sooruzhenij na transporte. Sankt-Petersburg, 2015. P. 206–215. (in Russian)
Review
For citations:
Utkin V.A., Kobzev P.N. ON PERFECTION OF CONSTRUCTIVE AND TECHNOLOGICAL FORMS OF PLATE AND RIBBED TRANSFER STRUCTURES FROM GLUED TIMBER. The Russian Automobile and Highway Industry Journal. 2019;16(1):76-89. (In Russ.) https://doi.org/10.26518/2071-7296-2019-1-76-89
Views:
1405
Email this article 