Standard series of transmitting equipment for hydra-jet technology based on dimensionless geometric parameters development
https://doi.org/10.26518/2071-7296-2024-21-2-180-189
EDN: USIPAL
Abstract
Introduction. The work is devoted to the calculation of series standards for the design of high-pressure transmission devices used in various hydra jet technologies, which will provide the design of these devices based on dimensionless indicators describing the relationship between their geometric and technological parameters.
Materials and methods. The methodology includes the use of mathematical models and analytical approaches to assess the influence of various parameters on heat generation processes in equipment, as well as methods for statistical processing of results.
Results. A histogram of temperature distribution was constructed and the data was approximated using the distribution curve of temperature values and parametric series were generated for dimensionless parameters depending on various factors such as temperature, pressure, rotational speed and linear speed. It is possible to obtain parametric series for linear dimensions from five temperature ranges and seven standard sizes depending on the pressure and rotation speed of the drill shaft.
Discussion and conclusions. The results obtained provide a better definition of the relationships between rotation speed, geometric characteristics and temperature parameters through the use of dimensionless indicators and it is possible to optimize the design of such devices taking into account operating conditions and ensuring increased efficiency.
Keywords
hydra-jet technologies,
hydro-puller device,
sealing,
parametric series,
standard series,
design optimization,
parameterization,
temperature
Supporting agencies: The article is published based on the results by the implementation of the SPbGASU grant 2024.
About the Author
V. I. Novikov
St Petersburg State University of Architecture and Civil Engineering
Russian Federation
Russian Federation
Vitaly I. Novikov. Cand. Sci., Associate Professor, Department of Forensics
Researcher ID: W-1648-2019
Krasnoarmeiskaya Str., St Petersburg, 190005
References
1. Borkowski P.J., Abramowski T, SzadaBorzyszkowska M, Szada-Borzyszkowski W. Comminution of Polymetallic Nodules with a HighPressure Water Jet. Materials. 2022; 15(22):8228. https://doi.org/10.3390/ma15228228
2. Barabas S., Florescu A. Reduction of Cracks in Marble Appeared at Hydro-Abrasive Jet Cutting Using Taguchi Method. Materials. 2022; 15(2):486. https://doi.org/10.3390/ma15020486
3. Shanab I.A., Sorensen A.D. Experimental and Statistical Study of High-Pressure Water Jet “Hydro-Demolition Technique” on Concrete for PartialDepth Concrete Bridge Deck Repair Applications. Transportation Research Record: Journal of the Transportation Research Board V. 2677, Issue 12, 2023 https://doi.org/10.1177/03611981231168842
4. Zhetessova G., Nikonova T., Gierz Ł., Zhunuspekov D., Yurchenko V., Zharkevich O. Preparation of the Surface of Long-Dimensional Rods of Hydro-Cylinders for Thermal Spraying Using an Abrasive Jet. Coatings. 2022; 12(10):1514. https://doi.org/10.3390/coatings12101514
5. Borkowski P.J., Szada-Borzyszkowski W. Micronization of Hard Coal with the Use of a HighPressure Water Jet. Energies. 2021; 14(16):4745. https://doi.org/10.3390/en14164745
6. Song J., Zhang H, Yu S., Su X. Application of integrated drilling and stamping technology in gas extraction through layer drilling. Energy Exploration & Exploitation. 2022; 40(4): 1113–1130. https://doi.org/10.1177/01445987221078053
7. Wang Z.-F., Shen S.-L., Modoni G. Enhancing discharge of spoil to mitigate disturbance induced by horizontal jet grouting in clayey soil: Theoretical model and application. Computers and Geotechnics 2019 V. 111, P. 222 https://doi.org/10.1016/j.compgeo.2019.03.012
8. Veropalumbo R., Russo F., Viscione N., Biancardo S.A. Rheological Properties Comparing Hot and Cold Bituminous Mastics Containing Jet Grouting Waste. Advances in Materials Science and Engineering. V. 2020. Article ID 8078527. 16 p. https://doi.org/10.1155/2020/8078527
9. Golovin K.A. Development of the design of the extender piercing installation for fixing unstable rocks. Izvestiya Tula State University” (Izvestiya TulGU). 2013; 1: 326–329. (In Russ.)
10. Novikov V.I. The Effect of the Morphology of Contact Surfaces on the Temperature Field Distribution in Devices for Jet-Grouting of Soils. Journal of Machinery Manufacture and Reliabilitythis, 2022, № 51(4), pp. 329–335. https://doi.org/10.3103/s1052618822020108.
11. Novikov V.I., Pushkarev A.E., Manvelova N.E. Modeling of the heat balance of elements of a drill hydraulic remover for inject cementation of soils during operation. Nauchno-tekhnicheskiy vestnik Bryanskogo gosudarstvennogo universiteta. 2020; 3: 404-410. (In Russ.) DOI: 10.22281/2413-9920-2020-06-03-404-410
12. Golovin K.A., Malikov A.A., Pushkarev A.E. Thermal mode of operation of high-pressure hydraulic puller at hydro jet grouting installations. Izvestiya Tula State University” (Izvestiya TulGU). 2015; 4: 46–52. (In Russ).
Review
For citations:
Novikov V.I. Standard series of transmitting equipment for hydra-jet technology based on dimensionless geometric parameters development. The Russian Automobile and Highway Industry Journal. 2024;21(2):180-189. (In Russ.) https://doi.org/10.26518/2071-7296-2024-21-2-180-189. EDN: USIPAL
Views:
245
Email this article 