Influtnce analysis of 09Г2С and 30MnB5 steels thermo cyclic treatment on strength characteristics of road construction machines working bodies

Introduction. The ways of increasing the reliability of road construction machinery operation are considered. As a result, an option is proposed to replace the used 09Г2С steel with 30MnB5 boron steel. Using the example of a motor grader blade, the force effects on this working body of the road construction machinery are analyzed. In order to increase the level of physical and mechanical characteristics of 09Г2С and 30MnB5 steels, they are additionally exposed to thermo cyclic treatment. The experimental studies about the influence of this type thermal action on the structure and properties of steels are described. The comparative analysis of the obtained characteristics allows making a conclusion about the possibility of the considered replacement.

Materials and methods. Through the metallographic analysis the influence of the number of thermal effects cycles on the grain size of steel is investigated. Alongside a set of physical and mechanical characteristics of these steels was determined at various stages of the thermo cyclic treatment.

Results. It was determined that an increasing the level of physical and mechanical characteristics of the studied steels is possible through the use of thermo cyclic treatment. This is achieved by producing a fine-grained metal structure with a higher strength. The dependence of the tensile strength and yield strength of the steels under investigation on the number of cycles of thermal action is considered. Some correlation relationships were selected to describe these dependencies. The relationship between the yield stress and ultimate strength of 09Г2С and 30MnB5 steels and the grain size is considered. All investigated dependencies are presented in graphical form.

Discussion and conclusion. Based on a comparative analysis of the complex of physical and mechanical characteristics, the conclusion about the possibility of replacing 09Г2С steel with 30MnB5 steel was made.

1. Scherbakov A.P., Pushkarev A.E., Manvelova N.E. Rabochie mekhanizmy stroitel’nyh mashin i sposoby tekhnologicheskogo obespecheniya prochnosti svarnyh soedinenij iz vysokoprochnyh stalej [Working mechanisms of construction machines and methods of technological ensuring the strength of welded joints made of high-strength steels]. Nedvizhimost’: ekonomika, upravlenie – Real estate: Economics, management, 2020, 1: 63–68. (In Russian)

2. Mukhametshina R.M. Otkazy dorozhno-stroitel’nyh mashin po parametram korrozii [Failures of road construction machines in terms of corrosion parameters]. Izvestiya KazGASU. – News of the University, 2013, no. 4 (26): 62–67. (In Russian)

3. Scherbakov A.P. Vybor materiala i metoda povysheniya iznosostojkosti elementov stroitel’nyh mashin [Material and method selection for increasing the wear resistance of construction machines components] // The Russian Automobile and Highway Industry Journal. 2020. № 17 (4). https://doi.org/10.26518/2071-7296-2020-17-4-464-475. (In Russian)

4. Scherbakov A.P. Eksperimental’nye issledovaniya vliyaniya termicheskoj obrabotki na svojstva svarnyh soedinenij rabochih mekhanizmov dorozhno- stroitel’nyh mashin // The Russian Automobile and Highway Industry Journal. 2020;17(6):664-675. https://doi.org/10.26518/2071-7296-2020-17-6-665-675. (In Russian)

5. Gordienko V.E., Trunova E.V., Abrosimova A.A., Shananina N.V. Passivnyy ferrozondovyy kontrol’dlitel’no ehkspluatiruemykh svanykh metallokonstruktsiy s korrozionnymi povrezhdeniyami [Passive ferrosonde monitoring of long-term operation of welded metal structures with corrosion damage]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2016, no. 3 (56): 193–197. (In Russian)

6. Polyansky, I. Sizov, U. Mishigdorzhiyn, V. Butukhanov. Improvement of the heat resistance of carbon steels by thermocycling thermochemical treatment with self-protective pastes based on boron carbide and aluminum // IOP Conf. Ser.: Mater. Sci. Eng. 116: 1-5.

7. Gordienko V.E., Abrosimova A.A., Trunova E.V., Scherbakov A.P. K vyboru konstrukcionnyh stalej dlya izgotovleniya svarnyh metallicheskih konstrukcij stroitel’nyh mashin [To the choice of structural steels for the manufacture of welded metal structures of construction machines]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2017, no. 6 (65): 233–238. (In Russian)

8. Floreen S., Hayden H.W. The deformation and fracture of stainlees steels having microduplex structures (Deformation characteristics and fracture strength of Cr-Ni stainless steels with fine scale two phase ferrite plus austenite microstructures). ASM Transactions Quarterly, 1968, vol. 61:489–499.

9. Berezina A.A. Nekotorye osobennosti ocenki strukturnoj i mekhanicheskoj neodnorodnosti svarnyh soedinenij metallicheskih konstrukcij stroitel’nyh mashin [Some features of evaluation of structural and mechanical heterogeneity of welded joints of metal structures of construction machines]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2015, no. 4 (51): 123–127. (In Russian)

10. Mylnikov V.V. Vliyanie chastoty nagruzheniya na ustalost’ konstrukcionnyh materialov [Influence of loading frequency on fatigue of structural materials]. Nauka i tekhnika – Science and Engineering, 2019, 5: 52–55. (In Russian)

11. Prokhorov V.Yu., Bykov V.V. Puti povysheniya dolgovechnosti i iznosostojkosti podshipnika skol’zheniya navesnogo tekhnologicheskogo oborudovaniya [Ways to increase the durability and wear resistance of the sliding bearing of mounted technological equipment]. NiKa, 2017, 1: 71–74. (In Russian)

12. Gordienko V.E., Abrosimova A.A., Trunova E.V. Vliyanie termociklicheskoj obrabotki na strukturnye izmeneniya plasticheski deformirovannyh svarnyh soedinenij metallicheskih konstrukcij stroitel’nyh mashin [Influence of thermocyclic processing on structural changes of plastically deformed welded joints of metal structures of construction machines]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2016, 2 (55): 174–180. (In Russian)

13. Bezlyudko G.Ya., Muzhitskiy V.F., Popov B.E. Magnitnyj kontrol’ (po koercitivnoj sile) NDS i ostatochnogo resursa stal’nyh MK [Magnetic control (by coercive force) VAT and residual resource of steel MK]. Zavodskaya laboratoriya. Diagnostika materialov – Factory laboratory. Diagnostics of materials. 1999, 9 (65): 53–57. (In Russian)

14. Gordienko V.E., Abrosimova A.A., Kuz’min O.V., Trunova E.V., Scherbakov A.P. Vliyanie termicheskoj i termociklicheskoj obrabotki na mekhanicheskie svojstva konstrukcionnyh stalej [Influence of thermal and thermocyclic treatment on the mechanical properties of structural steels]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2018, no.1 (66):128–133. (In Russian)

15. Zajtsev A.I. Perspektivnye napravleniya razvitiya metallurgii i materialovedeniya stali [Promising areas of development of metallurgy and materials science of steel]. Chernaya metallurgiya. Byulleten’ nauchno-tekhnicheskoj i ekonomicheskoj informacii. – Journal of Iron and Steel. Bulletin of Scientific, Technical and Economic Information, 2019, 75(4): 417–426. (In Russian)

16. Gordienko V.E., Abrosimova A.A., Trunova E.V., Korneeva E.A., Scherbakov A.P. Vliyanie strukturnyh parametrov konstrukcionnyh stalej na rezul’taty ocenki napryazhenno-deformirovannogo sostoyaniya svarnyh metallokonstrukcij [Influence of structural parameters of structural steels on the results of stress-strain state assessment of welded metal structures]. Vesnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2016, 6 (59): 194–199. (In Russian)

17. Morrison W. B. Superplasticity of low-alloy steels // ASM Transactions Quarterly, 1968, 61(3): 423–434.

18. Vedyakov I.I., Odesskij P.D. Sovremennye otechestvennye standarty i voprosy rasshireniya primeneniya metallicheskih konstrukcij v stroitel’stve [Modern domestic standards and issues of expanding the use of metal structures in construction]. Vestnik NIC “Stroitel’stvo” – Bulletin of SIC “Construction”, 2019, 3 (22): 42–53. (In Russian)

19. Gordienko V.E., Abrosimova A.A., Trunova E.V. Vliyanie termociklicheskoj obrabotki na strukturnye izmeneniya plasticheski deformirovannyh svarnyh soedinenij metallicheskih konstrukcij stroitel’nyh mashin [Influence of thermocyclic treatment on structural changes of plastically deformed welded joints of metal structures of construction machines]. Vestnik grazhdanskikh inzhenerov – Bulletin of Civil Engineers, 2016, 2 (55): 174–180. (In Russian)

20. Vedyakov I.I., Odesskij P.D., Gurov S.V. Obespechenie prochnosti svarnyh soedinenij dlya unikal’nyh konstrukcij iz prokata bol’shih tolshchin povyshennoj i vysokoj prochnosti [Ensuring the strength of welded joints for unique structures made of rolled products of large thicknesses increased and high strength]. Stroitel’naya mekhanika i raschet sooruzhenij – Construction mechanics and calculation of structures, 2018, 2 (277): 68–75. (In Russian)

21. Gustov Yu.I., Orekhov A.A. Issledovanie konstrukcionno- tekhnologicheskih i ekspluatacionnyh pokazatelej stroitel’noj tekhniki [Research of structural- technological and operational indicators of construction equipment]. Izvestiya KazGASU – News of the University, 2014, 4 (30):19–24. (In Russian)

22. Mukhametshina R.M. Влияние климатических факторов на свойства материалов и надежность дорожно-строительных машин [Influence of climat ic factors on the properties of materials and reliability of road construction machines]. Izvestiya KazGASU – News of the University, 2014, 4 (30): 102–108. (In Russian)

23. Meshkov Yu.Ya., Kotrechko S.A., Shiyan A.V. Rol’ prochnosti i mekhanicheskoj stabil’nosti v ocenke konstrukcionnogo kachestva stalej [The Role of Strength and Mechanical Stability in Evaluating the Structural Quality of Steels]. Vіsnik PDABA, 2013, 5 (182): 62–68. (In Russian)

24. Bublikov Yu.A. [Main directions of improving the properties of structural steels of ferrite-perlite class]. VEZHPT, 2014, 11 (72): 81–82. (In Russian)

25. Zaitseva M.M., Megera G.I., Kasyanov D.N. Problema dolgovechnosti detalej gruzovyh avtomobilej [The problem of durability of truck parts]. IVD, 2017, 2 (45): 71–75. (In Russian)