Сomparative analysis of efficiency of use a screw drill on frozen soil
https://doi.org/10.26518/2071-7296-2021-18-2-160-167
Abstract
Introduction. Drilling of frozen and permafrost soils is one of the complex and energy-intensive processes of earthworks. Drilling tools used on frozen soils implement the process of drilling the soil by deformation of cutting or crushing action. Current drilling tools are not efficient enough to use because they implement energy-intensive drilling processes and are not always suitable for various types of soils. A screw drill is considered, which implements the process of soil destruction by shear and shear deformation, which is less energy intensive.
Materials and methods. On the basis of theoretical studies of the interaction of 3 types of drilling tools with frozen soil, a comparative analysis was carried out to determine the efficiency of a screw drill use. The technical and economic indicators of the drilling process were compared. A method for determining the efficiency of the use a screw drill based on the analysis of special target functions is presented.
Results. The results of a comparative analysis of drilling tools have been obtained. Depending on the nature of soil deformation, the effectiveness of one drilling tool over another is determined. As a result of a comparative analysis of the drilling speed and the energy intensity of the drilling process, the efficiency of the screw drill was established.
Discussions and conclusion. In the course of the comparative analysis, the efficiency of the screw drill was determied, which implements shear deformation and soil separation, justifying the feasibility of further research.
About the Authors
I. G. MartiuchenkoRussian Federation
Igor G. Martyuchenko – Dr. of Sci., Professor, the Professor of the Transport Construction Department.
410054, Saratov, Politechnicheskaia Street
M. I. Zenin
Russian Federation
Maksim I. Zenin – Assistant of the Transport Construction Department.
410054, Saratov, Politechnicheskaia Street
References
1. Lev V. E., Lev V. E, Izzy M. K. Well drilling in permafrost regions: dynamics of the thawed zone. Polar Research. 2019, 38: 1-9.
2. Shan W. et al. Resistivity Model of Frozen Soil and High-Density Resistivity Method for Exploration Discontinuous Permafrost. Electrical Resistivity and Conductivity. 2017: 23-52.
3. Cao P. et al. Experimental study of the drilling process in debris-rich ice. Cold Regions Science and Technology. 2015, 120: 138-144.
4. Zubrzycki S. Drilling frozen soils in Siberia. Polarforschung. 2012, vol. 81, no. 2, pp. 151-153.
5. Arenson L. U., Springman S. M. Mathematical descriptions for the behaviour of ice-rich frozen soils at temperatures close to 0 C. Canadian Geotechnical Journal. 2005, 42(2): 431-442.
6. Gerasimov D. S. On the influence of the loading regime on the mechanical properties of frozen soils. Land transport and technological complexes and facilities. 2016: 73-77.
7. Yang Z. J., Still B., Ge X. Mechanical properties of seasonally frozen and permafrost soils at high strain rate. Cold regions science and technology. 2015, 113: 12-19.
8. Aksenov, V.I., Kal’bergenov, R.G. & Leonov, A.R. Strength Characteristics of Frozen Saline Soils. Soil Mechanics and Foundation Engineering. 2003, 40: 55–59 (In Russian)
9. Yang Y., Lai Y., Chang X. Laboratory and theoretical investigations on the deformation and strength behaviors of artificial frozen soil. Cold regions science and technology. 2010, vol. 64, no. 1, pp. 39-45.
10. Zhou G. et al. Laboratory investigation on tensile strength characteristics of warm frozen soils. Cold regions science and technology. 2015, 113: 81-90.
11. Timofeev N.G., Zhirkov A.N. Koncepcija razrabotki innovacionnogo porodorazrushajushhego instrumenta dlja burenija skvazhin v uslovijah kriolitozony [The concept of developing an innovative rock cutting tool for drilling in cryolithozone conditions]. Eurasian Union of Scientists. 2015, 4: 151-154.
12. Talalay P. G. Introduction to Ice Drilling Technology. Mechanical Ice Drilling Technology. Springer, Singapore, 2016, pp. 1-8.
13. Ivkin V.S., Alasheev M.O. Vlijanie fiziko-mehanicheskih svojstv gruntov na rabotu mashin dlja zemljanyh rabot [The influence of physical and mechanical proper ties of soils on the work of machines for earthworks]. Bulletin of UlSTU. 2015, no. 3, pp. 62-67. (In Russian)
14. Ivkin V.S., Vunberova N.P. Maloob#jomnye, rassredotochennye zimnie zemljanye raboty v stesnjonnyh uslovijah stroitel’stva [Small, dispersed winter earthworks in cramped construction conditions]. Vestnik of the Ulyanovsk State Technical University. 2018, 2: 52-55. (In Russian)
15. Valigura N. S. Sposoby burenija neglubokih skvazhin [Methods of drilling shallow wells]. Exploration and protection of the subsoil. 2014, 2: 27-30. (In Russian)
16. Timofeev NG, Skryabin RM, Yakovlev BV Povyshenie jeffektivnosti raboty porodorazrushajushhego instrumenta pri burenii skvazhin v mnogoletnemerzlyh porodah [Improving the efficiency of rock-cutting tools when drilling wells in permafrost]. Physical and technical problems of mining. - 2017. 6: 105-113. (In Russian)
17. Scriabin RM, Leontiev SN, Timofeev NG Burenie skvazhin bol’shogo diametra pnevmoudarnym klasterom v porodah vysokoj kategorii burimosti [Drilling of large-diameter wells with a pneumatic impact cluster in rocks of a high drillability category]. Geology and mineral resources of the North-East of Russia. 2017: 570-574. (In Russian)
18. Li H., Liu S., Chang H. Experimental research on the influence of working parameters on the drilling efficiency. Tunnelling and Underground Space Technology. 2020. 95: 103-174. https://doi.org/10.1016/j.tust.2019.103174
19. De Moura J. et al. Widening Drilling Operation: Performance Analysis on the Application of Fixed Cutter Drill Bits in Hard Rock Formation //International Conference on Offshore Mechanics and Arctic Engineering. – American Society of Mechanical Engineers, 2020. 84430:V011T11A078. https://doi.org/10.1115/OMAE2020-18836
20. Bugaev VG, Eresko SP, Bugaev IV Vybor racional’nogo ugla rezanija merzlyh gruntov pri burenii stroitel’nyh skvazhin [Choice of a rational angle of cutting frozen soils when drilling construction wells]. Stroitelnye i dorozhnye mashiny. 2018. 2: 30-36. (In Russian)
21. Bogomolov RM et al. Burenie dopolnitel’nyh bokovyh stvolov dolotami PDC [Drilling additional sidetracks with PDC bits]. Equipment and technologies for the oil and gas industry. 2018 2: 17-20. (In Russian)
22. Panin N.M., Bogomolov R.M. Sovershenstvovanie promyvki sharoshechnyh burovyh dolot [Improvement of flushing of roller cone drill bits]. Construction of oil and gas wells on land and at sea. 2020. 9: 11-14. (In Russian)
23. Serikov D. Yu. Analiz konstrukcij i tehnologij izgotovlenija tverdosplavnogo vooruzhenija sharoshechnyh burovyh dolot [Analysis of structures and manufacturing technologies of carbide weapons for roller-cutter drill bits]. Sfera. Oil and gas. 2017. 1: 30-35. (In Russian)
24. Darwesh A.K., Rasmussen T.M., Al-Ansari N. Controllable drilling parameter optimization for roller cone and polycrystalline diamond bits. Journal of Petroleum Exploration and Production Technology. – 2020. 10. (4): 1657-1674. https://doi.org/10.1007/s13202-019-00823-1
25. Sporin, Jurij, et al. “The characterization of wear in roller cone drill bit by rock material–Sandstone.” Journal of Petroleum Science and Engineering 2019. 173: 1355-1367. https://doi.org/10.1016/j.petrol.2018.10.090
26. Zhang, Jie, and Yang Hu. “Mechanical behavior and sealing performance of metal sealing system in roller cone bits.” Journal of Mechanical Science and Technology 2019. 33(6): 2855-2862. https://doi.org/10.1007/s12206-019-0533-5
27. Martyuchenko I.G., Zenin M.I. Perspektivy razvitija burovogo instrumenta dlja vechnomerzlyh gruntov [Prospects for the development of drilling tools for permafrost]. Construction and road machines. 2019. 9: 47-48. (In Russian)
28. Martyuchenko I.G., Zenin M.I. Vzaimodejstvie vintovoj lopasti burovogo instrumenta s merzlym gruntom [Interaction of a screw blade of a drilling tool with frozen soil. Scientific peer-reviewed] The Russian Automobile and Highway Industry Journal 2020; 17 (2): 162-171. https://doi.org/10.26518/2071-7296-2020-17-2-162-171 (In Russian)
29. Balovnev VI et al. Opredelenie optimal’nyh parametrov transportno-tehnologicheskih mashin metodami teorii podobnyh preobrazovanij [Determination of the optimal parameters of transport and technological machines by methods of the theory of similar transformations]. Construction and road machines. 2019; 12:.3-11. (In Russian)
Review
For citations:
Martiuchenko I.G., Zenin M.I. Сomparative analysis of efficiency of use a screw drill on frozen soil. The Russian Automobile and Highway Industry Journal. 2021;18(2):160-167. (In Russ.) https://doi.org/10.26518/2071-7296-2021-18-2-160-167