Interaction analysis of bucket bottom knife with soil to build up subbase

Introduction. To solve the problem of accelerating the construction of roads, improving their quality, it is advisable to use a continuous action unit to form a underlying layer. The main working elements of this unit are buckets, which cut off the soil layer from below and side. At the same time, the bottom knife cuts off the ground layer from below, the right knife - on the side, and the console knife partially cuts the top layer of soil from below for the next bucket. In particular, the analysis of interaction with the ground of the bottom knife of the continuous action unit is of theoretical and practical interest. To do this, the lower knife is divided into elements and the interaction of these elements with the soil is analyzed. The consistent impact on the soil of many bottom knives, within the width of the grip of the unit, is replaced by the impact on the ground of one conventional bottom knife at a distance necessary for the development of one cubic meter of soil. The forces of interaction of the conventional bottom knife with the soil are called conditional forces.
The method of research. The method of calculating energy costs when introducing the bottom knife into the ground is presented. In general, when introducing the bottom knife in the ground, there are energy costs: to separate the soil, to overcome the friction of the ground on the edge of the blade, to overcome the pressure of the ground on the face, to the rise of the ground, to the vertical acceleration of the ground by the phase, to overcome the friction of the ground on the face, to overcome the friction of the ground on the surface, to overcome the friction of the ground on the lower plane. The total energy costs of interacting with a one cubic metre soil are derived from the addition of private energy costs. The method of calculating the horizontal longitudinal force needed to move the bottom knife is given.
Results. On the basis of the developed method, energy costs are calculated in the introduction of the lower knife: on the separation of the soil, on overcoming the friction of the ground on the edge of the blade, on overcoming the pressure of the ground on the face, on the rise of the ground, on the vertical acceleration of the ground face, on overcoming the friction of the ground on the fascia, to overcome the friction of the ground on the lower plane. Energy costs to overcome the friction of the ground on the surface of the bottom knife are zero, as the soil flies over it. The total energy costs of the bottom knife interact with the soil of one cubic meter. The horizontal long-lived force needed to move the bottom knife has been determined.
Conclusion. As a result of the calculations: the energy needed to cut the ground with the bottom knives, about 5 kJ/cube m., horizontal longitudinal force needed to move the lower knife - 16 N. To determine the total energy costs of moving the boiler unit to remove the top layer of soil from the underlying layer of the road, you need to analyze the interaction with the soil of other elements of the bucket.

1. Nikolayev V.A. Opredelenie skorosti cepej i razmerov plasta grunta, otrezaemogo kovshom agregata dlya udaleniya verhnego sloya grunta s podstilayushchego sloya avtodorogi [Determining the speed of chains and the size of the soil layer cut off by the bucket of the unit to remove the top layer of soil from the underlying layer of the road]. The Russian Automobile and Highway Industry Journal. 2020; 1: 32-43. (in Russian)

2. Nikolayev V.A. Analiz vzaimodejstviya kromki lezviya konsol'nogo nozha s gruntom [Analysis of the interaction of the edge of the console knife blade with the soil]. The Russian Automobile and Highway Industry Journal. 2020; 2 : 172-181. (in Russian)

3. Nikolaev V.A. Analiz vzaimodejstvija pravogo nozha agregata nepreryvnogo dejstvija s gruntom [Analysis of the interaction of the right knife of the continuous action unit with the ground]. The Russian Automobile and Highway Industry Journal. 2020; 1: 32-43.

4. Zhuk A.F. Teoreticheskoe obosnovanie racio-nal'noj tekhnologicheskoj skhemy i parametrov rota-cionnogo pluga. [Theoretical justification of the rational technological scheme and parameters of the rotary plough]. Teoriya i raschyot pochvoobrabatyvayushchih mashin. 1989; 120: 145-153. (in Russian)

5. Popov G.F. Rabochie organy frez [Working bodies of milling cutters]. Materials VISHOM NTS. ONTI VISHOM. 1970; 27: 490-497. (in Russian)

6. Karasyev G.N. Opredelenie sily rezaniya grunta s uchyotom uprugih deformacij pri razrushenii [Determination of the ground cutting force taking into account elastic deformations during destruction]. Construction and road machinery. 2008; 4: 36-42. (in Russian)

7. Karnaukhov A.I., Orlovskiy S.N Opredelenie zatrat udel'noj energii na process rezaniya lesnyh pochv torcevymi frezami [Determination of specific energy costs for the process of cutting forest soils with end mills]. Construction and road machinery. 2010; 1: 20-22. (in Russian)

8. Kravets I.M. Opredelenie kriticheskoj glubiny rezaniya pri kombinirovannom rezanii gruntov gidrofrezoj [Critical depth of the cut determination in the combined cutting soil by hydromiller]. Construction and road machinery. 2010; 5: 47-49. (in Russian)

9. Kirillov F.F. Determinirovannaya matematich-eskaya model' vremennogo raspredeleniya tyagovogo usiliya dlya mnogorezcovyh rabochih organov zemlerojnyh mashin [Deterministic mathematical model of the traction force time distribution for multi-section working bodies of earth moving machines]. Construction and road machinery. 2010; 11: 44-48. (in Russian)

10. Berestov E.I. Vliyanie treniya grunta po poverhnosti nozha na soprotivlenie rezaniyu [Soil friction effect on the knife surface on cutting resistance]. Construction and road machinery. 2010; 11: 34-38. (in Russian)

11. Vershinin A.V., Subov V.S., Tyulnev A.M. Povyshenie effektivnosti diskofrezernyh rabochih mekhanizmov dlya razrabotki myorzlyh gruntov [Improving the efficiency of disc milling working mechanisms for the development of frozen soils]. Construction and road machinery. 2012; 8: 42-44. (in Russian)

12. Balovnev V.I., Nguen Z.SH. Opredelenie soprotivlenij pri razrabotke gruntov ryhlitelem po integral'nomu pokazatelyu prochnosti [Determination of resistance in the soil development with a ripper according to the integral strength indicator]. Construction and road machines. 2005; 3: 38-40. (in Russian)

13. Ryabets N., Kurzhner F. Weakening of frozen soils by means of ultra-high frequency energy. Cold Regions Science and Technology. 2003; 36: 115-128.

14. Liu X., Liu P. Experimental research on the compressive fracture toughness of wing fracture of frozen soil. Cold Regions Science and Technology. 2011; 65: 421 -428.

15. Talalay P.G. Subglacial till and Bedrock drilling. Cold Regions Science and Technology. 2013; 86: 142-166.

16. Sun X. ACT-timely experimental study on me-so-scopic damage development of frozen soil under triaxial shearing. Rock and Soil Mechanics. 2005; 8: 150-163.

17. Li Q. Development of Frozen Soil Model. Advances in Earth Science. 2006; 12: 96-103.

18. Atkinson J. The Mechanics of Soils and Foundations. CRC. Press. 2007; 448.

19. Balovnev V.I., Danilov R.G., Ulitich O.Yu. Issledovanie upravlyaemyh nozhevyh sistem zemlerojno-transportnyh mashin [Research of controlled knife systems of earth moving and transport vehicles]. Construction and road vehicles. 2017; 2: 12-15. (in Russian)

20. Nilov V.A., Fyodorov E.V. Razrabotka grunta skreperom v usloviyah svobodnogo rezaniya [Soil development with a scraper in free cutting conditions]. Construction and road machines. 2016; 2: 7-10. (in Russian)

21. CHmil' V.P. Nasosno-akkumulyativnyj privod ryhlitelya s avtomaticheskim vyborom ugla rezaniya [Pump-accumulator ripper drive with an automatic choice of a cutting angle]. Construction and road machines. 2016; 11: 18-20. (in Russian)

22. Kabashev R.A., Turgumbaev S.D. Eksperi-mental'nye issledovaniya processa kopaniya gruntov rotorno-diskovymi rabochimi organami pod gidrostaticheskim davleniem [Experimental studies of the soil digging process with a rotary-disk working bodies under the hydrostatic pressure]. The Russian Automobile and Highway Industry Journal. 2016; 4: 23-28. (in Russian)

23. Syomkin D.S. O vliyanii skorosti rabochego organa na silu soprotivleniya rezaniyu grunta [On the speed influence of the working body on the resistance strength to cutting soil]. The Russian Automobile and Highway Industry Journal. 2017; 1: 37-43. (in Russian)

24. Konstantinov Yu.V. Metodika raschyota soprotivleniya i momenta soprotivleniya rezaniyu pochvy pryamym plastinchatym nozhom frezy [Method for calculating the resistance and a resistance moment to cutting soil with a straight plate cutter knife]. Tractors and agricultural machines. 2019; 5: 31 -39. (in Russian)

25. Syromyatnikov Yu.N., Hramov I.S., Vojnash S.A. Gibkij element v sostave rabochih organov rotornoj pochvoobrabatyvayushchej ryhlitel'no-separiruyushchej mashiny [Flexible element in the working bodies of a rotary tillage and ripper separation machine]. Tractors and agricultural machines. 2018; 5: 32-39. (in Russian)

26. Parhomenko G.G., Parhomenko S.G. Silovoj analiz mekhanizmov peremeshcheniya rabochih organov pochvoobrabatyvayushchih mashin po zadannoj traektorii [Power analysis of mechanisms for moving working bodies of tillage machines along a given trajectory]. Tractors and agricultural machines. 2018; 1: 47-54. (in Russian)

27. Dranyaev S.B., CHatkin M.N., Koryavin S.M. Modelirovanie raboty vintovogo G-obraznogo nozha pochvoobrabatyvayushchej frezy [Modeling the operation of a screw l-shaped knife of a tillage mill]. Tractors and agricultural machines. 2017; 7: 13-19. (in Russian)